英文資料：
Horizontal ａnd vertical burning tester
A, scope of application:
In the laboratory, test method for sample placed on horizontal ａnd vertical direction with a small flame ignition ａnd combustion performance of the fuel
Two, horizontal ａnd vertical burning tester to meet the national standard:
ISO 1210 plastics －－ horizontal ａnd vertical sample ａnd the small flame ignition source contact,
Test method for performance of horizontal ａnd vertical burning GB/T 2408 plastic,
GB4609 vertical burning test
GB5455 textile fabrics - Determination of flame-retardant properties of vertical method
Characteristics of three, horizontal ａnd vertical burning tester:
Beautiful, generous, stable transmission, compact structure, large adjusting range, applying the flame time with automatic control, ａnd no electronic ignition device, convenient operation. And the result is reliable, ａnd provide the basis for the research of flame retardant materials, ａnd various materials comparison ａnd classification.
Four, the definition of:
1, vertical burning method: Determination of flammability in contact ignition source, including extinction time, scope ａnd time of flame spread, ａnd whether the combustion behavior of the material due to combustion of other substances caused by the material, comparison ａnd fire resistance grade.
ombustion method,
level 2: applicable to normal temperature, one end is fixed to a horizontal support, the other end of little plastic sample ｄrop 10mm or other self supporting materials quality control testing ａnd flammability classification test. Is a powerful means to control the material resistant quality ａnd evaluation of products.
3, textile fabric, flame retardant properties determination of vertical method: specifies a standard test method for determination of flame retardant fabric flame retardant performance, can be used to measure the tendency of fabric prevent combustion ａnd carbonization. For the determination of flame retardant requirements of clothing fabric, decorative fabric, flame retardant fabric, tent performance.
4, the flame
The required test conditions, remove the ignition, flame sustained burning material.
5, flaming time
The required test conditions, remove the ignition source, materials for flame combustion time.
6, flameless combustion
In the test specifications, remove the ignition source, when the flame combustion termination or non flame generated material keep the glow of combustion.
7, flameless combustion time
In the test specifications, when the flame combustion termination or remove the ignition source, material flameless combustion time.
Five, the principle of
Horizontal or vertical clamp one end of the specimen, a gas flame provisions on the sample free end, the combustion speed by measuring the linear （horizontal） or with flame ａnd flameless combustion time （vertical） combustion performance to evaluate the sample.
===============================================
Six, horizontal ａnd vertical burning tester technical indicators:
1, the sample size:
The sample size （125 ± 5） mm, （13 ± 0.3） mm wide, thick （3 ± 0.2） mm
After consultations between the parties concerned, also can use other thickness, but the maximum thickness should not exceed 13mm, ａnd should be noted in the test report.
Note: thickness, density, anisotropic material, pigment, filler ａnd the direction of flame retardant ａnd different content of a sample, the test results cannot be compared to each other.
2, the ambient temperature （standard）: （23 ± 2） ℃ relative humidity: （50 ± 5）%
3, the power supply voltage ａnd power: 220V ± 10%, 50HZ, 100W;
4, source: Industrial methane gas or other fuel gases （liquefied petroleum gas, used as natural gas, coal ａnd so on）
5, instrument appearance size: 720mm long width about "370mm" 850mm;
6, the timing device: accurate to 1s
7, thickness or micrometer: accurate to 0.01 mm
8, the best use of the medical absorbent cotton;
9, Bunsen flame applied time on three shifts: 10s, 12s, 30s;
10, the laboratory （Bunsen burner）:
Tube length was （100 ± 10） mm; diameter of （9.5 ± 0.3） mm;
11, the Bunsen burner tilt 45 degrees （adjustable）.
水平垂直燃燒測定儀
一、適用范圍：
在實驗室內，對水平和垂直方向放置的試樣用小火焰點火燃后的燃燒性能的試驗方法
二、水平垂直燃燒測定儀滿足國家標準：
ISO 1210塑料－－水平和垂直試樣與小火焰點火源接觸時、
GB/T 2408塑料燃燒性能試驗方法 水平法和垂直法、
GB4609垂直燃燒法
GB5455紡織物─阻燃性能測定─垂直法的
三、水平垂直燃燒測定儀的特點：
是外形美觀、大方、傳動平穩、結構緊湊、調整范圍大，施加火焰時間采用自動控制，并沒有電子打火裝置，操作方便。所得結果可靠，為研 究阻燃材料提供依據，以及將各種材料相互對比和分級。
四、水平垂直燃燒測定儀定義：
1、垂直燃燒法：可測定材料在接觸引燃源時的燃燒性能，包括熄滅時間，火焰蔓延的范圍及時間，以及由于該材料的燃燒行為是否引起 其它物質的燃燒方法，對材料進行對比及耐燃分級。
2、水平燃燒法：適用于常溫時，一端固定后能水平支撐，另一端下垂不大10mm的塑料試樣或其它自支撐材料的質量控制試驗和燃燒性的分類試驗。是控制材料耐燃質量和評價產品的有力手段。
3、紡織織物─阻燃性能測定─垂直法：規定了一種測定各種阻燃處理織物阻燃性能的試驗方法，可用以測定織物阻止燃燒及炭化的傾向。用于有阻燃要求的服裝織物、裝飾織物、帳蓬織物等阻燃發生性能的測定。
4、有焰燃燒
在規定的試驗條件下，移開點火源后，材料火焰持續的燃燒。
5、有焰燃燒時間
在規定的試驗條件下，移開點火源后，材料持續有焰燃燒的時間。
6、無焰燃燒
在規格的試驗條件下，移開點火源后，當有焰燃燒終止或無火焰產生時材料保持輝光的燃燒。
7、無焰燃燒時間
在規格的試驗條件下，當有焰燃燒終止或移開點火源后，材料持續無焰燃燒的時間。
五、水平垂直燃燒測定儀原理
水平或垂直地夾住試樣一端，對試樣自由端施加規定的氣體火焰，通過測量線性燃燒速度（水平法）或有焰燃燒及無焰燃燒時間（垂直法）等來評價試樣的燃燒性能。
六、水平垂直燃燒測定儀技術指標：
1、試樣尺寸：
試樣尺寸長（125±5）mm，寬（13.0±0.3）mm，厚（3.0±0.2）mm
經有關各方協商，也可采用其他厚度，但最大厚度不應超過13mm，并應在試驗報告中注明。
注：厚度、密度、各向異性材料的方向、顏料、填料及阻燃劑種類和含量不同一的試樣，其試驗結果不能相互比較。
2、環境溫度（標準要求）：（23±2）℃ 相對濕度：（50±5）%
3、供電電壓和功率：220V±10%、50HZ、100W；
4、氣源：工業級甲烷氣或其他燃料氣體（如家用液化石油氣，天然氣，煤氣等）
5、儀器外型尺寸約：長720mmⅹ寬370mmⅹ高850mm；
6、計時裝置：精確至1ｓ
7、測厚儀或測微計： 精確至0.01 mm
8、最好使用醫用脫脂棉；
9、本生燈對試樣施加火焰時間分三檔：10ｓ、12ｓ、30ｓ；
10、 實驗室燃燒器（本生燈）：
筒長為（100±10）mm；內徑為（9.5±0.3）mm；
11、 本生燈傾斜45°（也可調）。
